本產品主要用于各種玻璃、鋼化玻璃、汽車、彩晶玻璃、微晶玻璃、玻璃器皿、玻璃奶瓶、高硼硅玻璃、玻璃蓋板、玻璃鏡片、手機玻璃、家電玻璃、工業玻璃、日用玻璃、玻璃燈管、玻璃儀器等制品的絲印及移印。

2、產品特性：高亮光/平光啞光、附著力佳、快干、耐溶劑、耐高溫、耐摩擦、耐酸堿、抗腐蝕、耐水煮、耐刮傷環保無鹵素。

3、稀釋劑：用我司B-03專用稀釋劑或783開油，用718洗網水清洗網版。

4、固化劑：單組份使用，也可選擇添加我司JS-10專用固化劑用于增加油墨附著力及物理化學抗性。

5、油墨調配方法：開罐先攪拌均勻，取所需量油墨稀釋到合適印刷粘度。如需添加固化劑，先加固化劑攪拌后靜置10分鐘，待油墨與固化劑完全交聯后再進行稀釋。

6、干燥時間：常溫干燥，表干時間5-10分鐘，實干時間在24小時以內，80℃烘烤20分鐘可快速干燥。

7、添加固化劑后的使用時限：4-6小時，過期請棄用，剩余油墨不可回收。

【性能檢測】

1、3M膠帶劃百格測試：100%無脫落

2、耐沖壓測試：1mm厚鋁板180°折彎無變化。

3、耐酒精測試：用脫脂棉沾濃度99%工業酒精以500G力水平來回200次無脫色。

【注意事項】

1、先小量試印確認符合要求后再批量生產。

2、做好承印物的表面清除油脂及雜質工作，以促進附著效果。

3、附著力、硬度、耐酸性、耐酒精性、耐化學品性、抗劃傷性、耐磨性等性能的檢測，

需要完全固化后方可檢測。

4、未經允許情況下，不得將本系列油墨與其它類型油墨混用及配色。

5、油墨，稀釋劑使用及儲存時嚴禁煙火。

6、使用時注意施工場所的通風狀況良好，盡量避免皮膚直接接觸。

7、本品不慎濺入口、鼻、眼、耳內，應用大量水清洗或直接求助醫生。

This product is mainly used for all kinds of glass, toughened glass, automobile, color crystal glass, glass ceramics, glassware, glass bottles, high borosilicate glass, glass plate, glass lens, mobile phone glass, household glass, glass industry, daily-use glass, glass tube, glass and other equipment products and silk screen printing.

2, the product characteristics: high gloss / Matt matte, attachment Lijia, quick drying, solvent, high temperature resistance, friction resistance, acid and alkali resistance, corrosion resistance, boiling water resistance, resistance to scratching environment-friendly halogen-free.

3, the thinner: with our B-03 special thinner or 783 oil, 718 washing network water cleaning screen.

4, curing agent: use single component, choose to add our JS-10 special curing agent used to increase the ink adhesion and physical and chemical resistance.

5, ink deployment method: open the tank to stir evenly, take the required amount of ink to dilute the appropriate printing viscosity. For the need to add the curing agent, first add the curing agent after stirring for 10 minutes, until the ink and curing agent is fully cross-linked and then diluted.

6, the drying time: at room temperature, dry time 5-10 minutes, working hours in 24 hours, 80 degrees bake 20 minutes can be fast drying.

7, add curing agent after the use of time: 4-6 hours, please not expired, the remaining ink Unrecyclable.

[performance test]

1, 3M tape to draw 100 cell test: 100% no shedding

2, resistance to stamping test: 1mm thick aluminum plate 180 bending no change.

3, resistance to alcohol test: use skim cotton dipped in concentration of 99% industrial alcohol with 500G force level back and forth 200 times without decolorization.

[note] [note]

1, a small amount of the first test to confirm compliance with the requirements of mass production.

2, do a good job in the surface of the substrate to remove grease and impurities work to promote the attachment effect.

3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, wear resistance and other properties of the test,

Need to be fully cured rear can be detected.

4, without permission, may not use the series of ink and other types of ink mixing and matching.

5, ink, thinner use and storage is prohibited fireworks.

6, pay attention to the use of the construction site ventilation condition is good, try to avoid direct contact with skin.

7, the product accidentally splashed entrance, nose, eyes, ears, the application of a large number of water cleaning or directly to the doctor.